Book With Us Today!

 

 

The article below relating to How to Install a Bathtub is extremely enlightening. Read it for yourself and figure out what you think of it.

Mounting a bath tub isn't precisely brain surgery, but it does require strong plumbing, woodworking, as well as often, tiling skills. Replacing an old tub with a new one is also a moderately hard task. If the old tub is readily accessible, the task can relocate immediately; if you have to open up a wall to remove the old bathtub and also place the brand-new bath tub, the job is a lot harder. In either case, the project is within a residence handyman's abilities, although you will require a helper to vacate the old bathtub as well as set in the brand-new one. Make certain you have certified on your own for the job and also fit attempting it. Rather than working with a specialist to take over a halfway-completed task, it is much better to consider using one before you begin. Opportunities are you may require an expert plumber to make tube links.
This short article will assist you install a brand-new bathtub in your washroom if you have currently gotten a new bathtub and do not need to transform the plan of your previous water supply pipes.
Your devices as well as product checklist should make up the following:

 

• New Bathtub


• Hammer


• Pipeline Wrenches


• Prybar


• Safety Glasses


• Level


• Pliers


• Flexible Wrench


• Putty Knife


• Screwdriver


• Cold Knife


• Tape Measure


• Pipeline Caps


 

Preparing for the Installment

First of all, the sustaining frame supplied with the bathroom ought to be fitted (if called for) according to the producer's guidelines. Next, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is essential to see to it that if the tap includes a plastic washing machine, it is fitted in between the bath as well as the faucets. On a plastic bath, it is likewise reasonable to fit a supporting plate under the faucets device to avoid pressure on the bathtub.
Fit the versatile faucet connectors to the bottom of the two faucets using 2 nuts as well as olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet via the hole in the bath. Utilize the nut provided by the supplier to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Ensure you utilize all of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect the bottom of the overflow tube in a similar manner.The bath should now be ready to be fitted in its final position.

 

 

Removing Old Touches

If you require to change old faucets with brand-new ones as a part of your installment, after that the first thing you need to do is separate the water. After doing so, activate the faucets to drain pipes any kind of water continuing to be in the system. The procedure of getting rid of the existing faucets can be rather troublesome because of the restricted access that is often the case.
Make use of a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipes to the taps. Have a cloth all set for the continuing to be water that will certainly come from the pipelines. As soon as the supply pipelines have actually been eliminated, use the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary taps from turning throughout this procedure. When the taps have been removed, the holes in the bath/basin will certainly need to be cleaned up of any old sealing substance.
Prior to proceeding to fit the new faucets, contrast the pipe connections on the old faucets to the brand-new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the brand-new taps to fit.

 

 

Installing the Bathtub

Making use of the two wooden boards under its feet, position the tub in the required position. The wood boards are valuable in evenly spreading out the weight of the tub over the area of the boards rather than focusing all the weight onto four small factors.
The following goal is to ensure that the bathtub is leveled all round. This can be attained by inspecting the spirit level and readjusting the feet on the tub until the level checks out level.
To install faucets, fit the bottom of the outermost versatile tap port to the suitable supply pipeline by making a compression join; after that do the exact same for the other faucet.
Switch on the water as well as check all joints as well as new pipework for leakages and tighten them if essential. Fill the bath tub and additionally inspect the overflow electrical outlet as well as the regular outlet for leakages.
Lastly, deal with the bath paneling as defined in the producer's user's manual. Tiling and securing around the bath tub should wait till the bathtub has actually been used a minimum of when as this will resolve it into its final placement.

 

 

Suitable New Touches

If the tails of the new faucets are plastic, then you will require a plastic connector to avoid damage to the thread. One end of the adapter fits on the plastic tail of the tap as well as the various other end offers a link to the existent supply pipes.
If you require to fit a monobloc, then you will call for reducing couplers, which links the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next off, position the tap in the installing opening in the bath/basin guaranteeing that the washing machines remain in place between the faucet and the sink. Secure the faucet in position with the manufacturer offered backnut. When the faucet is firmly in place, the supply pipes can be attached to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with regular tap adapters. The former type ought to be attached to the faucet ends first, tightening just by hand. The supply pipelines can later on be connected to the other end. Tighten both ends with a spanner after both ends have actually been attached.

 

 

Tiling Around the Bath tub

In the area where the bath meets the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is important as the fitting can move enough to split an inflexible seal, creating the water to penetrate the wall between the bath and the tiling, resulting in issues with wetness and also feasible leakages to the ceiling listed below.
You can pick from a variety of coloured sealants to blend in your fixtures and fittings. They are sold in tubes and cartridges, and are capable of sealing gaps up to a width of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with spins of drenched paper or soft rope. Bear in mind to constantly load the bath tub with water prior to securing, to enable the motion experienced when the tub is in use. The sealant can crack fairly early if you do not take into account this movement prior to sealing.
Additionally, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are likewise quickly available on the market. It is advisable to fit the floor tiles utilizing water-resistant or waterproof glue and also cement.

 

How to Install or Replace a Bathtub

 

Find Your Dimensions

 

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

 

Disconnect the Water Supply and Drain Assembly

 

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

 

Cut Out the Old Tub

 

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

 

Install the New Tub

 

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

 

Secure the Tub

 

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

 

We had been guided to that report on Tools You Need to Install a New Bathtub from a friend on a different web page. Do you know another person who is sincerely interested in the subject? Be sure promote it. Many thanks for going through it.

Request Estimate